TOP

COLD Type Product Overview

Product Summary

Cold type peelable (#2001)

Product Features

#2001 SealPeel is a transparent liquid at room temperature, and the dried film can be easily peeled off as a single film.
It is used for surface protection and waterproofing of goods.

Application Method

The following three methods of application are available.

1.Applied by brush or roller
2.Spray application
3. Dipping (dobbing)

Packing

16kg can, 3kg can

Physical and chemical properties

Appearance Clear colorless liquid
Stinky Aromatic smell
Boiling point 86.5℃(toluene)
Specific gravity 0.89
Solubility insoluble in water
Volatile Existence
Flash point -0.5℃
Point of ignition 415℃

Usage

work environment

1.When working indoors, use a well-ventilated area where solvent vapors do not accumulate, and wear a gas mask for organic solvents.
2.Work in an area with fire extinguishing equipment.
3.If symptoms of solvent poisoning occur, seek immediate medical attention.

Foundation Preparation

1.Wipe off moisture, dust, and light oil with a rag, etc.
2.If there is a lot of oil on the surface, wash it with a solvent or detergent and dry it well.
3.Do not use on rubber, plastic or painted parts.

Tool Preparation

1.Open the paint container and mix with an appropriate stick until uniform.
2.Basically, use undiluted solution.
If it becomes difficult to apply, mix in 5-10% of a special thinner.
3.Use a rather large brush, soak it in thinner and squeeze it well when it becomes soft.

Painting method

1.Take a small amount of the thoroughly mixed seal peel in a saucer and apply it thickly enough that there is no dripping or running.
2.The trick is to apply one quick coat back and forth because if you go back and forth over one spot too many times, it will peel off on the brush.
3.When applying overlapping coats, make sure the surface is dry before doing so.
4.If the surface dries in about 1 hour after drying, it can be used.
However, it takes about 4-8 hours to dry, depending on the environment.
5.If the dried film starts to peel, it can be repaired by either repainting or brushing on seal peel in place of glue to fill the gaps in the film.

●Precautions for use

・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.

Cold type peelable(#3002)

Product Features

#Series 3002 SEALPEEL is a transparent liquid, adhesive-type paint at room temperature.

Application Method

The following three methods of application are available

1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)

Packing

16kg can, 4kg can

Physical and chemical properties

Appearance Opaque colored viscous liquid
Stinky Aromatic smell
Boiling point 108.5℃
Specific gravity 0.9
Solubility insoluble in water
Flash point 4.5℃
Point of ignition 363℃

Usage

Work environment

1.When working indoors, make sure the area is well ventilated and free of solvent vapors, and wear a gas mask for organic solvents.
2.Be careful of fire and work in an area with fire extinguishing equipment.
3.If symptoms of solvent poisoning occur, seek immediate medical attention.

Foundation Preparation

1.Wipe off moisture, dust, and light oil with a rag, etc.
2.If there is a lot of oil on the surface, wash it with a solvent or detergent and dry it well.
3.Do not use on rubber, plastic or painted parts.

Tool Preparation

1.Open the paint container and mix with an appropriate stick until uniform.
2.Use a rather large brush, soak it in thinner and squeeze it well when it becomes soft.

Painting method

1.Take a small amount of the thoroughly mixed seal peel in a saucer and apply it thickly enough that there is no dripping or running.
2.The trick is to work quickly, as it dries relatively quickly.

●Precautions for use

・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, provide adequate ventilation until completely dry.
・Store in a cool place out of direct sunlight.
・Be sure to see the SDS.

Cold Type Peelable(#8008)

Product Features

#Series 8008 SealPeel is an opaque brown liquid paint that can be peeled off at room temperature.
In addition to being effective against acid and alkali solutions, it is particularly effective in masking conversion coatings (black finish).

Application Method

The following three methods of application are available

1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)

Packing

16kg can, 4kg can

Physical and chemical properties

Appearance Opaque viscous liquid
Stinky Aromatic smell
Boiling point 108.5℃(toluene)
Specific gravity 0.866
Solubility insoluble in water
Volatile Existence
Flash point 6℃
Point of ignition 480℃

How to use

Usage

・Urethane, urethane, modified epoxy, acrylic silicone
・Wash primer
・Wood, tools, FRP resin, steps (landing)
・Glass, handrails, (parks, etc.) slip prevention
・Handles, concrete, mats, tiles
・Stone, impact prevention, etc.

Other uses are possible based on your ideas.

●Precautions for use

・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, provide adequate ventilation until completely dry.
・Store in a cool place out of direct sunlight.
・Be sure to see the SDS.

Cold Type Peelable(#8500)

Product Features

・Easy to handle with minimal dripping
・A tough, resilient film is formed.
・High frictional resistance and can be used as a non-slip surface
・Keeps rust away
・Excellent insulation, weather resistance (more than 1 year), water resistance, heat resistance, and cold resistance

Performance

※The test values below are for reference only and may vary depending on the environment such as temperature and humidity.

#1002-A #8500
Viscosity mPa・s 1300~1600 3000~4000
Dryness min Finger touch10/Curing60 Finger touch30/Curing120
Coating amount g/m2 【Brush coating】996 【Brush coating】532(*1)
【スプレー】520(*2)
Film thickness mm 【Brush coating】0.30 【Brush coating】532(*1)
【スプレー】520(*2)
Outdoor weather resistance 6 months 12 months

(*1)Two coats by brush
(*2)Undiluted solution 1:diluted material 1 (2 coats using the mixture shown at left)

Application Method

The following three methods of application are available

1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)

Packing

16kg can, 4kg can

Physical and chemical properties

Appearance Clear colorless liquid
Stinky Aromatic smell
Boiling point 108.5℃
Specific gravity 0.9
Solubility insoluble in water
Flash point 4.5℃
Flash point 363℃

How to use

Usage

・Urethane, urethane, modified epoxy, acrylic silicone
・Wash primer
・Wood, tools, FRP resin, steps
・Glass, handrails, (parks, etc.) slip prevention
・Handles, concrete, mats, tiles
・Stone, impact prevention, etc.

Other uses are possible based on your ideas.

●Precautions for use

・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・取り扱いの都度、容器は密封してください。
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.

Cold Type Peelable(#8501)

Product Features

・Easy to handle with minimal dripping
・A tough, resilient film is formed.
・High frictional resistance and can be used as a non-slip surface
・Keeps rust away
・Excellent insulation, weather resistance (more than 1 year), water resistance, heat resistance, and cold resistance
・No oil-based materials are used, so there is no risk of undermining.

Application Method

The following three methods of application are available

1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)

Packing

15kg can, 3kg can

Performance (compared to our products)

The test values below are for reference only and may vary depending on the environment such as temperature and humidity.

#1002-A #8501
Viscosity mPa・s 1300~1600 5000~7000
Desiccation min Feel10/Curing60 Feel30/Curing120
Coating amount g/m2 【Painting with a brush】996 【Painting with a brush】0.13
【Spray】0.07
Outdoor weather resistance 6 months 12 months

(*1) 2 coats by brush
(*2) undiluted solution 1 : diluted material 1 (2 coats by the left formula)

Physical and chemical properties

Appearance Opaque colored viscous liquid
Stinky Aromatic smell
Boiling point 101℃(MCH)
Specific gravity 0.77
Solubility insoluble in water
Flash point -3.5℃
Point of ignition 245℃

How to use

Usage

While #1002-A is suitable for use on metal surfaces, #8501 can be used on painted surfaces (*1) (primer) and provides excellent rust and scratch prevention. Due to its effectiveness, the top coat can be applied immediately after removal.
(*1)Patch test is required since it may adhere to the product depending on the conditions of use.

・Urethane, urethane, modified epoxy, acrylic silicone
・Wash primer
・Wood, tools, FRP resin, steps (landing)
・Glass, handrails, (parks, etc.) slip prevention
・Handles, concrete, mats, tiles
・Stone, impact prevention, etc.

Other uses are possible based on your ideas.

●Precautions for use

・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed after each handling.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.

Cold Type Peelable (#2001 Sustain)

Product Features

#2001 SealPeel is a clear liquid at room temperature, and the dried film can be easily peeled off as a single film.
It is mainly used for primary corrosion prevention, plating masking, and surface protection of goods.

Application Method

The following three methods of application are available

1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)

Packing

16kg can, 3kg can

Physicochemical Properties

Appearance Clear and colorless or green
Bad smell Organic solvent smell
Boiling point 90.35℃
Specific gravity 0.89
Solubility Water: insoluble, organic solvents: soluble
Volatile existence
Flash point -1℃
Point of ignition None

How to use

Usage

Primary rust prevention, protection, and stain prevention of parts and components
Masking during chrome plating process

●Precautions for use

・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.

Cold Type Peelable (#100 Sustain)

Product Features

It has a proven track record as a masking agent for chrome plating.
The environmentally friendly design allows for use by companies that have acquired ISO certification or have already obtained certification.

Application Method

The following three methods of application are available

1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)

Packing

16kg can, 3kg can

How to use

Usage

Masking during chrome plating

●Precautions for use

・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.

Cold type peelable (#8008MCH)

Product Features

Forms a translucent or red film to protect against dirt, scratches, rust, and chemicals.

Application Method

The following three methods of application are available

1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)

Packing

16kg缶、3kg缶

Physicochemical Properties

Appearance Clear colorless or red
Bad smell Solvent smell
Boiling point 78.7℃
Specific gravity 0.77
Solubility Water: insoluble Solvent: soluble
Flash point 5℃

How to use

Usage

Masking during chrome plating

●Precautions for use

・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.

Cold type peelable (#8008MCH)

Product Features

It can be used for a wide range of applications including furniture, instruments, plastics, and painted surfaces.
Viscosity adjustment facilitates spray application, which was an issue with #8501.
It is weather resistant and protects objects from rust and stains even outdoors (limited period).
In terms of film thickness, adhesion, and peelability, this product is standard in the SEALPEEL product line and is easy to handle.
Excellent heat and chemical resistance.

Application Method

The following three methods of application are available

1.Applied by brush or roller
2.Applied by spray
3.Dipping (dobbing)

Packing

14kg can, 3kg can

Physicochemical Properties

Appearance Clear colorless or red
Bad smell Solvent smell
Boiling point 101℃
Specific gravity 0.89
Solubility Water: insoluble Solvent: soluble
Flash point -4℃
Point of ignition 258℃

How to use

Usage

Prevention of stains and primary rusting of jigs and construction materials/construction equipment, rental equipment, etc.

●Precautions for use

・Use appropriate protection to prevent inhalation and contact with eyes, skin, and clothing.
・Containers should be sealed each time they are handled.
・Please handle fire with care.
・During and after use, please ensure adequate ventilation until the product is completely dry.
・Store in a cool place out of direct sunlight.
・Please be sure to read the SDS.

For inquiries about the seal peel COLD type, please contact

Contact us by phone

TEL:045-211-6740(Representative)
FAX:045-211-6741
Office hours: [weekdays].9:00~17:00(JST)

Contact us by e-mail

Mail Form